DpmStrSettings Setting Repository

DpmStrSettings

Role: Features tab page

Detailed role: Features tab page

The DpmStrSettings repository has the following characteristics:

• Primary Tab Page: /DPManufacturing/DNBDpmStructureWkb/Features
• Repository File: DNBDpmStructure
• Version: 1
• Full Compatibility: 1
• Upward Compatibility: 1

DpmStrSettings setting repository attributes:

• AddedMaterialMarginConfiguration
  Role: Margin to be added:
  • Type: integer
  • Default value: 1
• AddedMaterialMarginSize
  Role: Margin to be added:
  • Type: double
  • Default value: 0.01
• AlignmentLineExtremity
  Role: Default extremity
  • Type: short integer
  • Default value: 1
  • Values:

    0	None
    1	Start extremity only
    2	End extremity only
    3	Both extremities

• AlignmentLineLength
  Role: Length of the alignment mark:
  • Type: double
  • Default value: .150
• AlignmentLineOffset
  Role: Offset from attachment line extremities:
  • Type: double
  • Default value: .150
• AttachmentSmartNamingAttr
  Role: Attachment line Smart naming
  Detailed role: the label contain the attached product name
  
  • Type: short integer
  • Default value: 1
  • Values:

    1	TRUE
    0	FALSE

• BendingCurveAttribute
  Role: Generate curves
  • Type: short integer
  • Default value: 1
  • Values:

    1	TRUE
    0	FALSE

• DSTMultipatchAttr
  Role: Treat patches of the plate individually
  • Type: boolean
  • Default value: false
• EdgePrepType
  Role: Edge Prep Type
  • Type: integer
  • Default value: 0
  • Values:

    0	None
    1	Square
    2	Single_Bevel
    3	Single_Bevel_with_Shoulder
    4	Single_J
    5	DoubleBevel
    6	Double_Bevel_with_Shoulder
    7	Double_J
    8	Other Edge Prep.

• FitUpMarginConfiguration
  Role: Margin to be added:
  • Type: integer
  • Default value: 1
• FitUpMarginSize
  Role: Margin to be reduced by:
  • Type: double
  • Default value: 0.001
• FTATextGenAttr
  Role: To Generate 3D FTA text or to generate normal text
  • Type: boolean
  • Default value: false
• GenerateTabbedHolesWithLeadInOut
  Role: Generate tabbed holes with Lead In/Out
  • Type: short integer
  • Default value: 1
  • Values:

    1	TRUE
    0	FALSE

• LeadInLength
  Role: Lead In Length
  • Type: integer
  • Default value: 10
• LeadInLengthConfiguration
  Role: Lead in length:
  • Type: integer
  • Default value: 1
• LeadOutLength
  Role: Lead Out Length
  • Type: integer
  • Default value: 10
• LeadOutLengthConfiguration
  Role: Lead Out Length:
  • Type: integer
  • Default value: 1
• LeadSide
  Role: Lead Side
  • Type: integer
  • Default value: 0
  • Values:

    0	None
    1	Left
    2	Right

• NestingPackageType
  Role: Nesting Package
  • Type: integer
  • Default value: 0
  • Values:

    0	ALMA
    1	OPTINEST

• OpeningPrepType
  Role: Opening Prep Type
  • Type: integer
  • Default value: 0
  • Values:

    0	None
    1	Cut
    2	Marked

• PlateTemplate_RollLinesAttr
  Role: Number of roll lines:
  • Type: integer
  • Default value: 1
• ProfileTemplate_ComboExtremityAttr
  Role: Add to
  • Type: integer
  • Default value: 0
  • Values:

    0	None
    1	Start
    2	End
    3	Both

• ProfileTemplate_MarkZoneClearanceAttr
  Role: Marking zone clearance:
  • Type: double
  • Default value: 5
• ProfileTemplate_MinOverLapAttr
  Role: Minimum overlap:
  • Type: double
  • Default value: 450
• ProfileTemplate_OverLengthAttr
  Role: Over Length
  • Type: double
  • Default value: 55
• ProfileTemplate_StepValueAttr
  Role: Step value:
  • Type: double
  • Default value: 300
• TabWidth
  Role: Tab Width
  • Type: integer
  • Default value: 10
• TabWidthConfiguration
  Role: Tab width:
  • Type: integer
  • Default value: 1

Copyright © 1999-2019, Dassault Systèmes. All rights reserved.